German Huiyu reinforced adhesive steel adhesive, two-component epoxy adhesive steel adhesive. The building reinforcement material is A and B two-component modified epoxy structural adhesive. It is a type of adhesive suitable for fixing and then pouring adhesive steel. It is mainly used for pouring construction requiring high-strength bonding surfaces. Shandong reinforcement materials, Jinan reinforcement materials, Jinan adhesive steel glue, Shandong adhesive steel glue, Jinan carbon fiber cloth, Shandong carbon fiber reinforcement 021. Product features 02 · Winter construction does not crystallize, and the curing time is not extended (low temperature type). 02. Good operability, no layering, no separation, no precipitation, good thixotropy, no flowing construction, and can save the amount of glue used. 02. Types, which can solve construction technical problems under various harsh conditions (low temperature, high temperature, wet surface, underwater). 02. The material has high strength, excellent aging resistance and medium (acid, alkali, salt) resistance. 02. High bonding strength, good toughness and shock resistance. 02. The material is environmentally friendly, does not contain volatile solvents, and is safe. 02 II. Technical Index 02GB50728-2011 “Technical Specification for Safety Appraisal of Engineering Structural Reinforcement Materials” Class I Grade A Rubber 020202 III. Process Flow 02 Drilling → Surface Treatment → Fixed Steel Plate → Sealing and Exhaust Hole Setting → Dispensing and Filling → Curing and Maintenance → Inspection → Corrosion Treatment 02 IV, Scope of Application 02 Adhesive Steel Rubber 02 · Concrete Bonding reinforcement of components, masonry components, and wood components to steel plates. ·Curtain wall installation, bonding installation of marble, granite, tile, etc. ·Surface repair and bonding of concrete components and steel components. 02 perfusion adhesive steel 02 · concrete components wet outsourcing steel reinforcement, bridges and other components external large-scale steel plate pouring adhesive steel reinforcement · concrete cracks (1-5mm), internal defects (honeycomb, hole) grouting repair. ·Construction of anchor bolts, equipment bottom plate secondary grouting, epoxy resin self-flowing floor. 02 5. Instructions for use 02 Adhesive steel 02 · Clean the surface of the substrate: polish the adhesive surface to remove the surface slurry and loose layer, reveal the new surface and blow off the dust with an air compressor, and then use acetone to remove the dirt. ·Steel plate surface rust removal: It can be polished by sandblasting, sandblasting, or steel wire brush until a metallic luster appears. ·Weigh the required dosage according to A:B=3:1, mix thoroughly, apply to the surface of the steel plate to be bonded, with a thickness of 1-3 mm, and make the middle thick edge of the adhesive layer thin. ·After the steel plate is pasted in place, it should be fixed with chemical anchor bolts or expansion bolts immediately and pressurized appropriately. ·Do not move the adhesive until the glue is cured, so as not to affect the bonding effect. 02 Filling adhesive steel 02 · Clean the surface of the substrate: polish the adhesive surface to remove the surface slurry and loose layer, reveal the new surface and blow off the dust with a compressor, and then use acetone to remove the dirt. ·Steel plate surface rust removal: It can be polished with sandblasting, sandblasting cloth or steel wire wheel, etc., until a metallic luster appears. ·Place the steel in place and weld according to the design requirements, and then close the gap between the steel and the concrete with sealing glue or epoxy repair mortar. The injection hose and exhaust pipe must be buried in the appropriate places. ·Weigh the required amount in proportion, mix thoroughly, and pour the mixed pouring steel rubber into the pressure pump to start pouring. The glue injection order principle is from bottom to top. Do not move the adhesive until the glue is cured, so as not to affect the bonding effect. 02. Weight ratio: A:B=3:1; ·Reference dosage: 5~7Kg/m202