Circular formwork expertise Ⅰ column mold processing and wood cylinder formwork is used and made of resin; Ⅱ greatly improves work efficiency; Ⅲ cleans up debris inside the column steel bar; iv so the poured concrete surface is smooth and flat; after the cylindrical wood formwork is removed; vi through the steel pipe horizontal and vertical lap vertical; Ⅲ check whether the column vertical bar exceeds the circumference; Ⅲ 2 people pick up the column mold to the side of the column bar. Yuncheng wooden cylindrical mold manufacturer wholesale Oute building materials circular formwork transmission process principle: The main principle is that when concrete is poured, under the action of the side pressure of the concrete, the common sense of the already woody cylindrical template circular formwork is newly known every day to circle itself. Since the cylindrical wood formwork is poured with concrete again, the normal stress in each direction of the formwork is equal and can balance itself, so there is no need for a complicated external support system. Construction process: steel bar concealed acceptance → welded cross rebar → formwork brush mold release agent → column root cleaning, formwork in place → close the column mold and fix the steel belt bolt → adjust the column mold verticality → seal the column foot with mortar → pour concrete → remove the mold → clean the template (close the card and put it upright). Yuncheng wooden cylindrical mold manufacturer wholesale Oute building materials circular formwork installation method: clear the column base debris, pop up the column cross control axis, and pop up the outer tangent of the column circumference. Standard cylindrical stirrup column insert is adopted to ensure that the insertion is not biased. Check if the vertical bar of the column exceeds the circumference. If it exceeds, technical treatment should be carried out. Place the rebar pad. Cross reinforcing bars are arranged at the root, middle and top of the column respectively to ensure the reinforcement layer of the concrete column. Apply mold release agent to the female mouth of the mold. Two people pick up the column mold to the side of the column bar, erect the template, close the template, clamp it with multiple 50×30×3 steel strips, and align the bolt holes and tighten the interface bolts one by one. The vertical degree of the template is adjusted by fixing the scaffold, and the column foot is blocked with mortar. Yuncheng wooden cylindrical mold manufacturer wholesale Oute building materials circular formwork 02 formwork demolition and management: After the concrete strength of the column meets the requirements of the standard, the column mold can be removed and maintained according to the maintenance. When removing the formwork, the column foot mortar is chiseled off first, and then the steel strip is removed. The formwork automatically rises and opens the gap, and the two people can remove the formwork and remove it. Clean the formwork garbage and apply an isolator. When cleaning the formwork, do not damage the surface corrosion-resistant resin. Partially damaged templates can be repaired and reused, and templates with a large damaged area can be truncated to extend other templates. Cylindrical wood formwork should be placed vertically. When placed horizontally, only single-layer discharge is allowed, and stacked code is placed. The female and child mouths at the interface of the template are susceptible to damage by bumps. They must be prepared and must not be broken. Yuncheng wooden cylindrical mold manufacturer wholesale Oute building materials round formwork 02 Construction operation points: Check whether the formwork size is equal to the actual column size. Clean up debris and garbage inside the column reinforcement, and level the column foot; play the cross control line, and use the guide plate to determine the circumference line. The mold female mouth is painted with mold release agent. Close the column mold well, pay attention to the vertical tangent of the female mold to the circumference line, clamp the template with a steel belt, fix the steel belt in the upper, middle, and lower parts first to prevent the female and female mouth from being misaligned, and then tighten the other nuts in turn. In order to prevent the bolt from sliding due to excessive pressure on the side of the bottom template, double steel strips are used to connect or encrypt the spacing within the lower 1/height range. The hanging bucket collides with the column mold when lifting and pouring concrete in the circular formwork knowledge lecture hall. Pay attention to the thickness of the stratification when unloading concrete, and pay attention to the vibrator not touching the formwork when pouring concrete. Yuncheng wooden cylindrical mold manufacturers wholesale Oute building materials circle template